600-GD Gas Detector
BEPMARINE FD-2 Gas Detector
Gas detector with built-in visual/audible alarm to keep you safe! Monitor the gas box, bottle stowage, bilge or the area below the cooker/stove. The FD-2 has single-circuit monitoring without additional accessory connections.
Product details
BEPMARINE gas detectors should always be connected to the operating voltage, and therefore they have no on/off switch. This ensures maximum safety while you are on your boat or in your vehicle.
Explosive gas mixtures have a different density. Some are heavier than air and accumulate on the ground, others are lighter and rise, thus collect below the vehicle's roof.
You should always keep this in mind, when installing gas sensors!
By using the GD types with a second gas sensor, all potential hazards are taken into account and maximum safety is achieved.
For LPG and gasoline vapors that are heavier than air, mount the sensor near the ground, where the vapors are likely to accumulate.
For CNG vapors that are lighter than air, mount the sensor in the area of the ceiling, but not above cooking or heating equipment!
BEPMARINE 600-GD
A second gas sensor can be connected to the 600-GD. This way you can monitor the gas box, bottle stowage and the bilge or the area below the cooker/stove.
Each monitoring circuit is equipped with a separate 3-color control LED which indicates the respective system status: during normal function: green, in the case of system errors: yellow and in the event of an alarm: red.
An internal, acoustic alarm (piezo buzzer) as well as additional connections for further external alarm transmitters (e.g. item 23403) or a fan complete the device's safety features.
The system may be tested by means of the "TEST" button.
Dimensions (WxHxD): 88 x 67 x 17 mm / 2.4" x 3.5" x 0.7". Operating voltage: 10-32 volts.
Optical (LED) and acoustic (piezo) signals for sensor 1 and 2*
LED GREEN - no explosive gas mixture, no signal tone
LED YELLOW - sensor error detected, slow beep
LED RED - alarm, gas present, quick alarm sound
Signal tone medium/slow - warm-up phase - all LEDs flash yellow
Signal tone quick - ALARM - LED lights up red
Signal tonre slow - sensor error - LED lights up yellow
All details at a glance
- Microprocessor control
- *Two monitoring circuits can be used
- Self-test possible
- Built-in visual and audible alarm
- *Connection for further external alarm devices
(Load capacity max 800 mA @ 12 V, with larger currents use an additional relay) - *Connection for one fan (maximum load capacity 800 mA @ 12 V, for larger currents use an additional relay)
- Operating voltage: 10-30 V DC
- Current consumption 350 mA max.
- Required fuse 2 A
- Sensitivity 20% LEL (lower explosion limit)
- Surface or rear mounting (max 2.5 mm panel wall thickness)
- Dimensions (WxHxD) 88 x 67 x 17 mm / 3.5" x 2.4" x 0.7"
- Electrical connection on the back of the device via one/*two connector strip/s with screw terminals
The connections are clearly marked- + POSITIVE 10-32 volt DC (via fuse 2 A)
- - NEGATIVE wiring system
- B * POSITIVE control output for fan or relay (max 800 mA @ 12V)
- A * POSITIVE control output for external audible alarm (max 800 mA @ 12V)
- C * NEGATIVE for external audible alarm and fan (or relay)
(NEGATIVE of the cylinder valve is connected to NEGATIVE electrical system, not with connection C!) - R Red sensor connection cable (sensor 1)
- G Green sensor connection cable (sensor 1)
- B Black sensor connection cable (sensor 1)
- R * Red sensor connection cable (sensor 2)
- G * Green sensor connection cable (sensor 2)
- B * Black sensor connection cable. (Sensor 2)
BEPMARINE gas sensor BL-SL-L
- Housing dimensions Ø x H: 42 x 21 mm
- Connection cable Ø x L: 3.5 mm x 5 m, wire colors red / green / black
- Distance between mounting screws: 37 mm
- 2 Phillips self-tapping screws 1.9 x 13 mm included
The sensor must be mounted in an area that is protected against (bilge or splash) water.
If the gas sensor gets wet, it is no longer safe/ready for operation and must be replaced!
The original gas sensor as a second sensor or spare can be ordered here.
Documents
Customers also bought
Similar items
Customers ask customers
Ask other SVB customers who have already purchased this product from us about their experience.
Your question will be automatically forwarded to other SVB customers and published on the product page. Please do not ask any questions which can only be answered by the SVB team – such as the status of an order or product availability. You are also more than welcome to contact our SVB team by email at: info@svb24.com or by phone on: +49 (0)421 57290510 .